DECKING AND FELTING THE ROOF - Dallas Area Habitat
Construction Manual April 2011 Roofing Chapter, Page 1 of 7 Construction Manual . Chapter 4 : overlap so that water runs over and not under the drip edge (Figure 2). At the peak of the Felt paper may then be applied to the entire roof. Nail with button caps along edges of ... Return Doc
PerformaInstall FrontPg 8-06 - Metal Roofing Materials For ...
Performa Steel Shingle’s patented four-way interlock design guards against 30# Felt + Ring Shank Roofing Nail Solid Substrate* Panel Installation Detail Apply drip edge over felt paper at gable. Make sure to overlap the drip edge at the ... View This Document
FOR USE UNDER ASPHALT SHINGLES ONLY
Say goodbye to traditional asphalt saturated felt paper and Break free plus 1” (i.e. 22” horizontal overlap) is recommended, vertical end laps should be 12” overlap and anchored 1” in from the edge. Roof slopes ... Get Doc
Installation Instructions - Benjamin Obdyke
Install roofing felt over entire roof deck. Felt should extend 1/4" beyond edge of roof deck. Overlap layers at least 4" working toward the ridge. 3. Tack down Cedar Breather. One tack (or nail) Install felt and Cedar Breather onto roof deck per instructions. ... Content Retrieval
General Instruction 12.4 - Conestoga Log Cabins And Homes
Attach paper using 1'' long roofing cap nails. Nail the felt only where necessary to hold it in place and along the outside edges. Repeat this process on the other roof half. Cut off excess paper at top and sides. 21 Use line on paper for overlap. ... Retrieve Content
Property Care White Papers Roofing: Wood Roof Installation ...
Property Care White Papers Roofing: Wood Roof Installation Details Historic New England, 2010 Page 3 of 4 Felt Paper and Spun Fiberglass Mesh Installation ... Access Full Source
Light Gauge Metal Roof And Wall Panels
Light Gauge Metal Roof and Wall Panels Installation Guide for Delta Rib, Delta Rib III, Nor-Clad®, Strata Rib® & 21⁄ 2 Corrugated ... Document Viewer
The felt paper need not overlap the valley flashing (the valley metal can be laid right on top of the felt). SLATE ROOFING — TOOLS OF THE TRADE THREE TYPES OF SLATE CUTTERS: PEARSON (ABOVE) STORTZ (LEFT) FREUND (RIGHT) STORTZ SLATE RIPPER (RIGHT) ... Doc Retrieval
Bituminous Waterproofing - Wikipedia, The Free Encyclopedia
Roofing felt (formerly tar paper) is the base material used to make roof shingles and roll roofing. Typical uses of felt paper are as an underlay(ment) ... Read Article
Aquabar B Installation Guide - Fortifiber
Than roofing felt and poly film. Aquabar “B” slows moisture migration and is a superior vapor retarder. coated paper or other materials to trap moisture Be sure to overlap tub, ... Read Full Source
Roofing Underlayment - felt, Ice And Water Barrier, Synthetic ...
This video reviews most popular types of roof underlayment used in asphalt roof installation produced by GAF / ELK roofing - American leading roof manufacturer by volume. 1) Deck Armor breathable synthetic underlayment 2) ShingleMate - basic roofing felt (tar paper) 3) Weather Watch ... View Video
Tar paper - Wikipedia, The Free Encyclopedia
Tar paper is distinguished from roofing felt which is impregnated with asphalt instead of tar, Older construction sometimes used a lighter-weight tar paper, stapled up with some overlap, as a water- and wind-proofing material on walls, ... Read Article
Guide - EDCO Products
ROOFING PRODUCTS, BUT DUE TO SPACE 6” vertical overlap .) 3: Use underlayment cut to 18” wide and provide 6” of vertical overlap on hips, Installing Synthetic underlayment or #30 felt paper Check to see that no nails or staples are protruding from the ... Read Content
SELF-ADHERING MODIFIED BITUMEN ROLL ROOFING For Flat roofs
SELF-ADHERING MODIFIED BITUMEN ROLL ROOFING for flat roofs a bit of the release paper on the back side, just enough to expose the adhesive surface. along the line at the bottom of the selvage of the sheet it will overlap. ... View Full Source
For 5V-Crimp Panel - Best Buy
For 5V-Crimp Panel L 1652 South Lee Hwy. Cleveland, TN 37311 Lower roof pitch requires a greater amount of panel overlap. All end-lap applications require two horizontal rows overlaid with felt paper. Codes allow re-roofing over shingles without the use ... Access Full Source
Roofing Tile - About.com Home
Tile roofs are typically laid over 30# to 45# roofing paper or roofing felt and have a plywood roof substrate or in some cases roof batten strips. Concrete tiles usually have about a 3" overlap. Related Articles. Pros and Cons of Using Tile Roofing; Choosing a Roofing Material; Asphalt Shingle; ... Read Article
Shingle Installation Guide - Eco-$mart
Top/Bottom Lap Joint Upper Panel Lower Panel 30# Felt+ Ring Shank Roofing Nail Solid Substrate* 30# Felt Ring Shank Roofing Nail 2” x 5/16” Painted/ Gasketed Screw Apply drip edge over felt paper at gable. Make sure to overlap the drip edge at the eave line. 2. ... Fetch Here
Why Or Why Not Install Rolled Roofing - About.com Home
Several types of roll roofing are used as supplements to other roofing materials; one example is saturated felt, Why (or Not) to Install Rolled Roofing About Home Follow us: We deliver. Get the best of About Home in your inbox. Sign up. Thanks for signing up! There was an error. ... Read Article
Installation Guide - Best Buy
When re-roofing determine if existing roofing needs to be removed . For new construction, it is recommended to use ice and water shield instead of #30 felt paper . overlap valley 4" and put 2 rows of silicone between ... Fetch Document
DIY- How To Roof A House- Section 3 Of 6 Installing Felt ...
Http://www.DoItYourSelfBuilder.com Video Project Tilted: Roofing With The Pros this is 3 of 6 videos samples taken from the full 60 min video. We will show you step by step how to remove an old wood roof, install plywood sheeting, felt paper and install a new 30 year comp roof. To ... View Video
Skyline Roofing - ASC Building Products
Skyline Roofing Installation Guide • August 2015 1 Table of asphalt saturated felt paper. Some synthetic underlayments may be used in place of felt with Overlap the end a minimum of 6” when starting a new roll of felt. ... Visit Document
W Deck Defense High Performance Roof Underlayment Roof ...
Pattern and overlap lines speed installation • High-traction, ™ vs. Organic Felt underlayment of using Deck Defense™ High Performance Roof Underlayment. Install following the roofing manufacturer’s application instructions. ... Content Retrieval
No comments:
Post a Comment